️🚨 This product is no longer manufactured
The descriptions and diagrams below are for information only.
HeatMaster® 100 N
High performance combined boiler and water heater
- ALSO AVAILABLE IN PROPANE
- TANK-IN-TANK TECHNOLOGY
- label_energy_FUEL
- Boilers
- DHW Production
- Standard
- Floor installation
# GTIN : 5400891032336
# P/N : A1002071
- Stainless steel Tank-in-Tank design
- 69.9 kW (HeatMaster® 70 N) or 107.0 kW (HeatMaster® 100 N) Outputs.
- Choice of Burner:
- Low NOx Premix gas or LPG
- Forced draught natural gas or LPG
- Pressure jet 28 sec or 35 sec oil
- Can also be used as a stand alone water heater
- Anti –Legionellae: hot water stored at a consistently high temperature
- Built-in primary circuit shunt HEP pump, internal expansion vessels, safety valve and low water pressure switch
- Control panel including thermostats, combined temperature and pressure gauge, indicators and on/off switch
- Stove enamelled casing
- The Heatmaster can be used in conjunction with the Smart and Jumbo storage tanks, supplying even the largest hot water requirement
- Vented or unvented use, mains pressure Systempak available.
- Cold water inlet
- Automatic air vent.
- Water thermostat.
- Primary expansion vessels.
- Low water pressure switch.
- Control thermostat.
- Primary circuit safety valve.
- Boiler charge HEP pump.
- Rigid polyurethane insulation.
- Flue reduction collar.
- Turbulators.
- Heating circuit flow.
- Domestic hot water outlet.
- Internal stainless steel tank.
- Stainless steel thermostat pocket for DHW.
- Primary circuit.
- Flue pipes.
- Heating circuit return.
- Drain valve.
- Combustion chamber.
Constructive characteristics |
||
|---|---|---|
| Capacity (total) | 290 | L |
| Capacity (primary) | 160 | L |
| Capacity (domestic hot water) | 130 | L |
| Capacity expansion tank(s) | 2 x 10 | L |
| Chimney connection | 150 | Ømm |
| Connection - heating | 1 ½ F | Ø" |
| Connection - DHW | 1 M | Ø" |
| Connection - safety valve | 1/2 M | Ø" |
| Max operating temperature | 90 | °C |
| Water pressure drop boiler at Δt = 20°C | 83 | mbar |
| Max service pressure heating (primary) | 3 | bar |
| Max service pressure (DHW) | 8,6 | bar |
| Weight (empty) | 320 | kg |
Heating characteristics |
||
| Pre-heating time from 10 to 80°C (Heat source: boiler) | 21 | min |
| Heating time from 10 to 90°C | 36 | min |
Combustion |
||
| Input max (heating) HCV | 118,9 | kW |
| Input max (heating) LCV | 107 | kW |
| Efficiency at 30% load (EN15502-1) | 96,4 | % |
| Efficiency (max output) 80/60°C | 90,5 | % |
| NOx weighted (GCV) (EN15502) | 99,9 | mg/kWh |
| NOx class (EN15502) | 5 | |
| Output power max (80/60°C) | 96,3 | kW |
Domestic hot water performance |
||
| Peak flow at 40°C | 898 | L/10’ |
| Peak flow 1st hour at 40°C | 3168 | L/60’ |
| Continuous flow at 40°C | 2776 | L/h |
| Peak flow at 45°C | 774 | L/10’ |
| Peak flow 1st hour at 45°C | 2676 | L/60’ |
| Continuous flow at 45°C | 2379 | L/h |
| Peak flow at 60°C | 510 | L/10’ |
| Peak flow 1st hour at 60°C | 1811 | L/60’ |
| Continuous flow at 60°C | 1665 | L/h |
Electrical Characteristics |
||
| Voltage | 230 | V |
| Frequency | 50 | Hz |
| Protection IP | 30 | |
| Electrical consumption | 95 | W |
| Electrical power requirements | 0,4 | A |
Search on acv.com
A keyword, a reference, a range, a product,...
